Are you on the lookout for insight about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to eliminate the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also embeded in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will certainly aid you install a brand-new bath tub in your bathroom if you have currently acquired a new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product list should comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather problematic because of the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Using both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bath tub has actually been used at the very least once as this will resolve it into its final setting.
Planning for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about Tools You Need to Install a New Bathtub and I am hoping you enjoyed my piece. Kindly take the opportunity to promote this blog post if you enjoyed reading it. Thanks a lot for your time. Kindly come visit our website back soon.
Click For More Info